Top 10 Best boss truck amplifier sub

Top 10 Rated boss truck amplifier sub in 2021 Comparison Table

Bestseller No. 1
BOSS Audio Systems R6002 - Riot 1200 Watt, 2 Channel, 2 4 Ohm Stable Class AB, Full Range, Bridgeable, Mosfet Car Amplifier with Remote Subwoofer Control
  • 600 W MAX Power @ 2 Ohm x 2 Channels
  • 300 W MAX Power @ 4 Ohm x 2 Channels
  • 1200 W MAX Bridged Power @ 4 Ohm x 1 Channels
  • Full-Range, Class A/B Topology, MOSFET Power Supply
  • Low and High Level Inputs, Variable Filter, Variable Bass Boost
Bestseller No. 2
BOSS Audio Systems KIT2 8 Gauge Amplifier Installation Wiring Kit - A Car Amplifier Wiring Kit Helps You Make Connections and Brings Power To Your Radio, Subwoofers and Speakers
  • 20 Foot / 8 Gauge Red Power Cable, High Quality Competition Fuse Holder
  • 3 Foot - 8 Gauge Black Ground Cable
  • 16 Foot / 18 Gauge Blue Turn-On Wire, 30 Foot / 16 Gauge Speaker Wire
  • 20 Foot High Performance RCA Interconnect, 6 Foot Split Loom Tubing
  • (20) 4" Wire Ties, (3) Rubber Grommets
Bestseller No. 3
BOSS Audio Systems BAB10 Amplified Car Subwoofer - 1200 Watts Max Power, Low Profile, 10 Inch Subwoofer, Remote Subwoofer Control, Great for Vehicles That Need Bass But Have Limited Space
  • BUILT-IN AMPLIFIER: A built-in 1200 Max watt amplifier powers the subwoofer
  • PULSE WIDTH MODULATED: This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
  • VARIABLE LOW-PASS FILTER: A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • HIGH LEVEL INPUTS: Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB10 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • LOW LEVEL INPUTS: Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB10 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
Bestseller No. 4
BOSS Audio Systems PT1600 2 Channel Car Amplifier – Phantom Series, 1600 Watts, Full Range, Class A/B, 2-8 Ohm Stable, Mosfet Power Supply, Bridgeable
  • Power - 800 Watts Max x 2 @2-Ohms 400 Watts Max x 2 @4-Ohms 1600 Watts Max x 1 Bridged @4 Ohms
  • Full Range - With a Full Range amplifier you not only have the option to run your speakers but also your subwoofers
  • Class A/B Topology - Class β€˜A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal Class β€˜B’ amplifiers have no current flowing through its outputs with no audio signal
  • Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
  • Variable Gain Control - The gain control is not for adjusting volume It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier
Bestseller No. 5
BOSS Audio Systems CUBE8 Car Subwoofer and Amp Package – Built-in Amplifier, 8 Inch Subwoofer with Passive Radiator, Remote Subwoofer Control
  • Built-in Amplifier - A built-in 400 Max watt amplifier powers the 8” subwoofer
  • Passive Radiator – A driver unit that has its motor structure (magnet) removed, becomes a passive diaphragm. As a result, there is no Chuffing that you would generally get with a ported box, thus enriching the BASS & making the system more linear
  • Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the CUBE8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • Phase Control - Phase control lets you adjust the speaker phase with the amplifier if your speakers or subwoofer are hooked up β€œout of phase”
SaleBestseller No. 6
BOSS Audio OX4KD Class D Car Amplifier – 4000 Watts, 1 Ohm Stable, Digital, Monoblock, MOSFET Power Supply
  • POWER: 4000 Watts Max x 1 @1-Ohm, 2000 Watts Max x 1 @2-Ohms. DIMENSIONS: The OX4KD is 14.3 inches in Depth, 7 inches in Width and 2.3 inches in Height. It weighs 7.8 lbs.
  • CLASS D: Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
  • 1 OHM STABLE: Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
  • STRAPPING CAPABLE: You are able to strap TWO OX4KD amplifiers and double the power that is being sent to your subwoofer(s). You now have the ability to connect more subwoofers to take advantage of the extra power
  • WARRANTY: BOSS Audio Systems provides a powerful 6 year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality
Bestseller No. 7
Kicker 44TCWC104 10" 600W Complete Subwoofer Bass Package with Loaded Subwoofer Enclosure, Boss 1500W Monoblock Car Amplifier and 8 Gauge Wiring Kit
  • COMPLETE SOUND SYSTEM: Upgrade your car's sound system with this complete amplified bass package bundle that includes: 10" subwoofer, an enclosure, a mono block amplifier, and an 8-gauge wiring kit
  • CAR SUBWOOFER: This Kicker 4-ohm subwoofer boast 600 watts max power and 300 watts RMS; Sensitivity: 98.4 dB
  • CAR AMPLIFIER: The Boss AR1500M Armor Series 1500 Watt Mono Car Amplifier delivers 700 watts RMS at 4 ohms to power your subwoofer; Includes a remote bass control
  • SUBWOOFER BOX ENCLOSURE: This Kicker enclosure features a custom port design and is made with sturdy MDF construction and thick black carpet; Dimensions: 21.5 x 15 x 4 / 7.625 inches (W x H x Top Depth / Bottom Depth)
  • WIRING AMP KIT: 20-foot 8 gauge red power cable; 1/4-inch gold plated ring terminal; 3-foot 8 gauge black ground cable; Number 10 gold plated ring terminal; 16-foot 18 gauge blue turn on wire; 20-foot high performance RCA interconnect; (3) Rubber grommets; 30-foot speaker wire; 5/16-inch Gold plated ring terminal; 6-foot split loom tubing; (20) 4-inch wire ties
SaleBestseller No. 8
BOSS Audio Systems R1004 4 Channel Car Amplifier – Riot Series, 400 Watts, Full Range, Class A/B, 2 Ohm Stable, IC (Integrated Circuit) Great for Car Speakers and Car Stereos
  • Power - 100 Watts Max x 4 @2-Ohms, 50 Watts Max x 4 @4-Ohms
  • Class A/B Topology - Class β€˜A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class β€˜B’ amplifiers have no current flowing through its outputs with no audio signal
  • Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
  • Variable Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier
  • Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
Bestseller No. 9
BOSS Audio Systems AR1500M Car Amplifier - 1500 Watts Max Power, 2 4 Ohm Stable, Class AB, Monoblock, Mosfet Power Supply, Remote Subwoofer Control
  • POWER: Maximum Power Output of 1500 Watts at 2 Ohms into one channel. MAX Power Output of 750 Watts at 4 Ohms into one Channel. This amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to
  • HIGH LEVEL INPUTS: Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the AR1500M to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
  • LOW LEVEL INPUTS: Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the AR1500M with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
  • LOW-PASS CROSSOVER: A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
  • SWITCHABLE BASS BOOST: Switchable Bass Boost allows you to boost the low bass +18db.
Bestseller No. 10
Rockville RVE12CA 12" Slim Vented Powered Car Subwoofer Enclosure, 1400 Watts
  • Rockville RVE12CA Slim 12” 1400 Watt Amplified Car Subwoofer in Vented Enclosure, 1400 Watts Peak power output, 350 Watts RMS, 12β€œ Super-Slim Subwoofer, Ultra-Stiff Composite Pulp Cone with Kevlar Reinforcement, 3D Molded Acrylic Dust Cap, Expanded & Rolle
  • Vented Core Magnet Motor Structure, 2” High Temperature Aluminum Voice Coil, 8mm Washer & Yoke Plates, 13. 6mm Peak-to-Peak X-Max, 50oz. Magnet, Slim Vented MDF Enclosure Design, Aviation Grade Black Tweet Carpet with Embroidered Logo, Black Texture Synthet
  • Frequency response: 30Hz-500Hz, SPL @ 1w/1m: 89dB, Dimensions: 24.2" Length x 15.2" Height 5.5" Top Depth x 7.5" Bottom depth
  • Built-in 300 Watts RMS / 1200 Watt Mono Block Amplifier, 150mV – 5V Variable Input Level, 12dB Low Pass Crossover Frequency 50Hz-250Hz, Low Level RCA Inputs, High Level Speaker Level Input with Auto Start Music Sense, RJ11 Jack for Dash Mounted Bass Remote

Are you searching for top 10 good boss truck amplifier sub on the market in 2021? Our AI system had scanned more than 52,373 customer satisfaction about top 10 best boss truck amplifier sub in 2021, we have come up with the top 10 rated products you may be interested in. We have ranked the best brands from Artificial Intelligent and Big Data, as you see below:

Our Best Choice: Boss Audio 12″ 1400W Car Audio Subwoofer & 1500W Mono Class A/B Amplifier with 8 Gauge Wiring Kit & QPower Single 12″ Vented Subwoofer Enclosure Box


Our rating:4.9 out of 5 stars (4.9 / 5)






This motor vehicle audio deal incorporates a Manager Audio 1400-watt subwoofer, 1500-watt amplifier with a distant and wiring kit, and a Q-Power enclosure. Give your car’s audio method additional bump with the ultimate effectiveness and higher ability of the Manager Audio CX122 12-Inch 1400-Watt Subwoofer. Offering 1400 watts of max electricity and a 700 watt RMS ability ranking, the Manager CX122 sub delivers with its major-stamped metal body, solitary 4-ohm voice coil and a tailor made-tooled, injected cone. It also capabilities an performance of 94 dB and frequency reaction of 25Hz-3kHz. You, yeah you, you need to have some extra bump in your auto and the Manager Armor 1500W Monoblock Amplifier with 8-gauge wiring package is the one particular that delivers the jams in your ride. As a Class A/B amplifier with a MOSFET energy supply, it presents you crystal very clear and crisp acoustics as you push down the open up road. It is 2-Ohm stable to generate a lot more electrical power and additional volume and is whole of characteristics that will leave you speechless. It reveals off switchable bass improve, variable get control, a variable lower-go filter, significant and very low-stage inputs, thermal protection, and a subwoofer amount command that provides you the means to raise the sub amount when an amp or subwoofer are linked. It has a peak electricity of 1500 watts at 2 Ohms, RMS ability of 1125 at 2 Ohms, peak ability of 750 watts at 4 Ohms, and RMS energy of 563 watts at 4 Ohms. This amplifier also arrives with an 8-gauge wiring set up kit for your usefulness. The Q Electricity 12-Inch One Hefty Duty Vented Subwoofer Enclosure options strong 5/8-inch MDF development, charcoal carpet covering, a twin vented style, and terminal cup connectors.

12-INCH SUBWOOFER: 1400 watts max electricity 700 watts RMS ability Single 4 ohm 2-inch voice coil Custom made tooled, injected cone Performance: 82 dB Frequency response: 25Hz 3kHz Mounting depth: 5.4 inches Warranty: 3-12 months warranty
1500-WATT MONO AMPLIFIER: Monoblock, Class A/B, MOSFET Electric power Source Large and Reduced Amount Inputs RMS Power: 563 watts x 1 channel @ 4 ohms 1125 watts x 1 channel @ 2 ohms Max ability: 750 watts x 1 channel @ 4 ohms 1500 watts x 1 channel @ 2 ohms THD: .01% S/N ratio: >105dB Dimensions: 10.31 x 6.5 x 2.56 inches Warranty: 6-12 months warranty
8-GAUGE WIRING Kit: 20 ft. 8 Gauge Crimson power cable Opposition significant excellent fuse holder 1/4″ Gold plated ring terminal 3 ft. 8 Gauge Black ground cable #10 Gold plated ring terminal 16 ft. 18 Gauge Blue flip on wire 20 ft. Significant effectiveness RCA interconnect (3) Rubber grommets 30 ft. Speaker wire 5/16″ Gold plated ring terminal (20) 4″ Wire ties
12-INCH SUBWOOFER ENCLOSURE: 5/8-inch MDF design Volume: 1.65 cubic feet Tuned to 42 Hz Solitary chamber, slot port vent design and style Tough charcoal carpet covering Pounds: 22 lbs . Proportions: 15 x 17 x 13 inches Guarantee: 2-year guarantee

Leave a Comment