Top 10 Best adafruit audio amplifier

Top 10 Rated adafruit audio amplifier in 2021 Comparison Table

Bestseller No. 1
Audio IC Development Tools Adafruit Mono 2.5W Class D Audio Amplifier - PAM8302 (1 piece)
  • This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC.
  • Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic "LM386" amps!
  • The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin to ground. The output is "Bridge Tied" - that means the output pins connect directly to the speaker pins, no connection to ground.
  • Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Speaker is not included, use any 4 ohm or greater impedance speaker.
Bestseller No. 2
Adafruit Stereo 2.1W Class D Audio Amplifier - TPA2012
  • Output Power: 2.1W at 4Ω, 10% THD, 1.4W at 8Ω, 10% THD, with 5V Supply
  • PSRR: 77 dB typ @ 217 Hz with 6 dB gain
  • Designed for use without an output filter, when wires are kept at under 2"-4" long
  • Four pin-selectable gains: 6dB, 12dB, 18dB and 24dB. Select with the onboard switches or by setting the G0 and G1 breakout pins
  • Low current draw: typ 6mA quiescent and 1.5uA in shutdown mode
SaleBestseller No. 3
Stereo 20W Class D Audio Amplifier - MAX9744
  • Power From 4.5V-14V Dc Voltage
  • Up To 93% Efficient (88-93% Typical)
  • 20Ma Quiescent Current (Or Put Into Shutdown For 1Ua Quiescent)
  • Up To 29.5Db Max Gain
  • Use Dc Or Ac Coupled Line-Level Input, Up To 3Vpp.Filterless Spread-Spectrum Modulation Lowers.20W Stereo Output (4&Amp;Omega;, Vdd 12V, Thd+N 10%).Low 0.04% Thd+N.Integrated Click-And-Pop Suppression.Short-Circuit And Thermal-Overload Protection
Bestseller No. 4
Audio IC Development Tools Stereo 3.7W Class D Audio Amplifier (1 Piece)
  • Spread-Spectrum Modulation and Active Emissions Limiting
  • Excellent click-and-pop suppression
  • Thermal and short-circuit/over-current protection
  • Passes EMI limit unfiltered with up to 12 inches (30 cm) of speaker cable
Bestseller No. 7
HiLetgo PAM8302 2.5W Class D Single Channel Solo Audio Amplifier Board Amp Module
  • PAM8302 2.5W Class D Single Channel Solo Audio Amplifier Board
  • Audio Amplifier Board Amp Module
  • Output Power: 2.5W at 4¦¸, 10% THD
  • 5.5V Supply 50dB PSRR at 1KHz
  • Output Power:1.5W at 8¦¸, 10% THD
SaleBestseller No. 8
Adafruit 4367 Circuit Playground TFT Gizmo - Bolt-on Display + Audio Amplifier
  • ets you add a lovely color display in a sturdy and reliable fashion
  • This PCB looks just like a round TFT breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections.
  • Once attached you'll get a 1.54" 240x240 IPS display with backlight control,
  • two 3-pin STEMMA connectors for attaching NeoPixel strips or servos, and a Class D audio amplifier with a Molex PicoBlade connector that can plug one of our lil speakers.
  • 53.3mm x 53.3mm x 9.4mm / 2.1" x 2.1" x 0.4"
Bestseller No. 9
Adafruit Audio FX Sound Board - WAV/OGG Trigger with 16MB Flash
  • Designed for people who wanted to make props, costumes, toys, and other small portable projects.
  • Completely stand-alone, just needs a 3 to 5.5VDC battery. No microcontroller required!
  • Built in Mass Storage USB with 16 MB storage. Drag and drop your files right on it.
  • High Quality Sound - decoding hardware handles any bit/sample rate and mono or stereo
Bestseller No. 10
Adafruit Pro Trinket LiIon/LiPoly Backpack Add-On
  • Comes assembled and tested
  • Uses the 5V input via Micro-B USB connector on the Pro Trinket
  • For charging single Lithium Ion/Lithium Polymer 3.7/4.2v batteries (not for older 3.6/4.1v cells)
  • 100mA charge current, adjustable to 500mA by soldering a jumper closed
  • Batteries and Pro Trinket not included.

Are you finding for top 10 best adafruit audio amplifier on the market in 2021? Our AI system had scanned more than 24,599 customer satisfaction about top 10 best adafruit audio amplifier in 2021, we have come up with the top 10 rated products you may be interested in. We have ranked the best brands from Artificial Intelligent and Big Data, as you see below:

Our Best Choice: Adafruit Circuit Playground Express Developer Edition – Base Kit


Our rating:4.8 out of 5 stars (4.8 / 5)






Package contains:

Circuit Playground Categorical – Developer Version
USB cable – A/MicroB – 3ft
3 x Alkaline AAA batteries
3 x AAA Battery Holder with On/Off Change, JST, and Belt Clip
Mini Storage Box

This is some of the fantastic goodies baked in to just about every Circuit Playground:

10 x mini NeoPixels, just about every one particular can screen any coloration
1 x Movement sensor (LIS3DH triple-axis accelerometer with faucet detection, free-tumble detection)
1 x Temperature sensor (thermistor)
1 x Gentle sensor (phototransistor). Can also act as a colour sensor and pulse sensor.
1 x Audio sensor (MEMS microphone)
1 x Mini speaker with course D amplifier (7.5mm magnetic speaker/buzzer)
2 x Drive buttons, labeled A and B
1 x Slide swap
Infrared receiver and transmitter – can receive and transmit any remote manage codes, as properly as send messages among Circuit Playground Expresses. Can also act as a proximity sensor.
8 x alligator-clip helpful input/output pins
Contains I2C, UART, 8 pins that can do analog inputs, multiple PWM output
7 pads can act as capacitive contact inputs and the 1 remaining is a true analog output
Inexperienced “ON” LED so you know its powered
Purple “#13” LED for primary blinking
Reset button
ATSAMD21 ARM Cortex M0 Processor, running at 3.3V and 48MHz
2 MB of SPI Flash storage, utilised principally with CircuitPython to store code and libraries.
MicroUSB port for programming and debugging
USB port can act like serial port, keyboard, mouse, joystick or MIDI!

Leave a Comment